
सेल फ़ोन के अंदर आपके कॉलर के आवाज़ जिस सुनते है उसे स्पीकर कहते है यह इलेक्ट्रिकल साउंड को वोइस में बदल देता है इसे earpiece भी कहते है यह मोबाइल के अंदर PCB पर टॉप में लगा होता है अगर यह ख़राब हो जाये तब आप कालिंग के समय आवाज़ नहीं सुन पाएंगे
The sound of your collar inside the cell phone is called the speaker, it turns the electrical sound into a voice. It is also called earpiece. It is placed in the top of the PCB in the top if it gets deformed. Can not hear the voice
स्पीकर एक धातु के वायर (copper ) को चुम्बकीय धातु (Metal) के चारो ओर प्लास्टिक का आवरण बना दिया जाता है आवाज़ के दोरान इसमें कपान होता है और इसी मैकेनिकल वाइब्रेशन के कारण मिलने वाली इलेक्ट्रिकल वोल्टेज को वोइस में बदल जाती है
The speaker A metal wire is made around the metal around the metal, the plastic is wrapped around the sound, and the electrical voltage that gets due to this mechanical vibration is converted into a voice.
The speaker A metal wire is made around the metal around the metal, the plastic is wrapped around the sound, and the electrical voltage that gets due to this mechanical vibration is converted into a voice.
स्पीकर की खराबियाँ - स्पीकर से आवाज सुनाई नहीं देने की खराबियाँ क्या है-
· कॉल के दैरान स्पीकर से आवाज नही आना
· स्पीकर से आवाज धीरे आना
· स्पीकर से आवाज साफ नही आना
No sound from the speaker during the call
· Slow noise from the speaker
· No clear sound from the speaker
स्पीकर की खराबियों का सॉल्युशन- स्पीकर की सभी खराबियों को ठीक करना।
1. मोबाइल सेटिंग में वॉल्युम का स्तर चैक करे।
2. मोबाइल सेट को खोलकर मल्टीमीटर से स्पीकर चैक करे |
3. सही स्पीकर 28ohms से 32ohms के बीच रेजिस्टेंस देते है
4. मोबाइल PCB प्लेट पर स्पीकर टच करने वाले पॉइंटो को स्क्रैच करे। कार्बन लग जाने के सप्लाई रूक जाती है |
5. PCB प्लेट को क्लीनर (ACTONE) से वॉश करे।
6. वायर वाला स्पीकर को हो तो दुबारा सोल्ड करे।
7. स्पीकर ख़राब होने पर स्पीकर नया लगाये
8. स्पीकर टिप्स पर कोल्ड टेस्टिंग करे | अगर कोई रीडिंग नहीं आ रही है तो स्पीकर सेक्शन की सर्किट ट्रेसिंग करे |
2. मोबाइल सेट को खोलकर मल्टीमीटर से स्पीकर चैक करे |
3. सही स्पीकर 28ohms से 32ohms के बीच रेजिस्टेंस देते है
4. मोबाइल PCB प्लेट पर स्पीकर टच करने वाले पॉइंटो को स्क्रैच करे। कार्बन लग जाने के सप्लाई रूक जाती है |
5. PCB प्लेट को क्लीनर (ACTONE) से वॉश करे।
6. वायर वाला स्पीकर को हो तो दुबारा सोल्ड करे।
7. स्पीकर ख़राब होने पर स्पीकर नया लगाये
8. स्पीकर टिप्स पर कोल्ड टेस्टिंग करे | अगर कोई रीडिंग नहीं आ रही है तो स्पीकर सेक्शन की सर्किट ट्रेसिंग करे |
1. Check the volume level in the mobile settings.
2. Open the mobile set and check speaker with multimeter.
3. The correct speaker gives resistance between 32ohms from 28ohms
4. Scratch the Speaker Touching Points on Mobile PCB Plate. Supply of carbon to stop stops.
5. Wash the PCB plate with the cleaner (ACTONE).
6. If the wired speaker is to be sold then reload.
7. Speaker new when the speaker is defective
8. Do cold testing on speaker tips. If no reading is coming, then trace the circuit of the speaker section.
9. कोल्ड टेस्टिंग करने पर दोनों
टिप्स पर रीडिंग 250 ohms से 600 ohms के बीच आना चाहिए
10.
स्पीकर सेक्शन में ज्यादातर कएल सीरीज कनेक्शन
में लगी होती है और डायोड और कापसिटर पैरेलल कनेक्शन में लगे होते है |
11.
यदि कन्नेक्शन टुट गया है तो जम्पर करो । और यदि कोई कॉम्पोनेन्ट ओपन या शोर्ट हो गया है तो रिप्लेस करे |
12.
अगर
रेजिस्टेंस पूरी सप्लाई में कही न मिले तब Audio IC (COBBA पुराने
मोबाइल में / CODEC नए मोबाइल में )
पर हल्की हीट दे या रीसोल्ड करे |
13.
Audio IC के बॉल ड्राई सोल्ड हो
जाने IC को रिबॉल करो |
14.
ऑडियो IC नए मोबाइल फ़ोन में पॉवर IC में लगी होती ह
15.
ऑडियो IC से CPU IC तक की सप्लाई को चेक करे l CPU IC को चेक करे l
On cold testing, the readings on both tips should be between 250 ohms and 600 ohms.
10. Most QL series in speaker section is connected in connection and diodes and copeter are connected in parallel connection.
11. If the connection is torn then jumper should be done. And if a compton is open or shortened then replace it.
12. If the resistance can not be found in the full supply, then give a light heat or reset to the Audio IC (COBBA in old mobile / CODEC new mobile).
13. Recharge the IC with the audio IC ball becoming dry sold.
Notes -
- All China Mobile Speaker Circuit Diagram - Speaker Jumper picture solution
- Xiaomi Redmi Note 3 Ear Piece Not Working ( Receiver Not Working Solution with Jumper Picture
- IPhone 6 Ear Speaker Jumper Ways Earpiece Solution
- Sony Z Ultra C6802 Ear Speaker Jumper Ways Earpiece Solution ( Step by Step Solution)
- Sony C3 D2502 Ear Speaker Jumper Ways Earpiece Solution ( Step by Step Solution)
स्पीकर खराबी को ठीक करने के जरूरी Tips- स्पीकर से आवाज कम व बिल्कुल धीरे से सुनाई देने पर स्पीकर बॉडी के छेद साफ करे व स्पीकर को नया लगाये।
Asia Telecom " Mobile Training Institute "
Get Admission Call - 9644139972
One Month - Full Hardware & Software
Address - Jabalpur, Madhya Pradesh
24500 Total (Include - Hostel + Fooding) + OCA Training + Microscope Training.
Batch – Every Month of 28 Date
One month daily 6 to 7 hour classes (AC Class)
No copy pen allow in our class
All Mobile +keypad + android + iphone+ All section tracing
IC Reballing + Resoldering
+
All mobile software Umt+Miracle+z3x
full training with box and Without box complete Flashing with particle
All mobile FRP unlock
All Mobile mode Flashing Error Solution
4 TB Tested Flash File HDD - (2000 extra)
Limited sheet only